MSI-GT2/3 Series Linear Position Sensor with Analog Output

THE SCOPE OF SUPPLY INCLUDES:

Linear position sensor

Certificate of Conformity

Manual

Warranty card

Mating connectors and magnets for the sensor must be ordered separately!

TECHNICAL REQUIREMENTS FOR ORDER PLACEMENT

1

2

3

4

5

6

MSI-GT2

.

M

.

0

5

0

0

.

T

.

D60

.

A

0

1

1

Series:

MSI-GT2 – two independent channels

MSI-GT3 – three independent channels

2

Flange type:

M – M18 × 1.5, rod Ø10 mm

3

Measuring range:

0025...3800 mm, 1 mm step

Other lengths available on request

4

Zero point:

T - 50 mm from flange / 60 mm damping zone

5

Connection:

D60 – 6-pin male connector, M16

S32 – 8-pin male connector, M16

H02 – PUR cable without connector, 2 m; option: H01...H20 (1...20 m)

6

Output signal:

1 output with 1 position magnet

A01 - 4…20 mA

A11 - 20…4 mA

V01 - 0…10 V

V11 - 10…0 V

* Measuring range is programmable

Measured value

Position

Operating range, L

25 — 3800 mm, 1 mm step

Displacement speed

up to 10 m/s

Update rate

0.5 ms up to 1200 mm; 1.0 ms up to 2400 mm; 2.0 ms up to 3800 mm

INTERFACE

Analog interface

For voltage (control input impedance: > 5 kΩ)

For current (min./max. load resistance: 0/500 Ω)

Number of magnets

1

Max cable length

For stable operation, it is recommended to use a cable no longer than 35 meters

POSITION MEASUREMENT ACCURACY

Linearity

< ± 0.01 % F.S. (minimum ± 40 µm)

Repeatability

< ± 0.001 % F.S. (minimum ± 2.5 µm)

OPERATING CONDITIONS

Operating temperature

-40 °C…+75 °C

Rated pressure

350 bar, 600 bar peak

Humidity

90 % rel. humidity, no condensation

Ingress protection

IP65, IP67 at cable outlet

MATERIALS

Sensor electronics housing

Aluminum, plastic

Sensor rod

Stainless steel ASTM A269-13 / TP304l (10x1.5)

Flange

Stainless steel 08Х18Н10 / AISI 304

MOUNTING

Mounting position

Any orientation. For horizontal installation of sensors with an operating range exceeding 1000 mm, the rod must be supported or fixed at the end

Flange parameters

Flange thread M18×1.5

Position magnet mounting

Mounting hardware and screws made of non-magnetic material

ELECTRICAL CONNECTION

Operating voltage

+24 V DC (–15 % / +20 %)

Reverse polarity protection

up to –30 V DC

Overvoltage protection

up to 36 V DC

Current consumption

50…140 mA (depending on sensor length)

Insulation resistance

500 V DC (between sensor housing and 0 V DC)

STANDARDS, EMC TESTS

Shock test

100 g, single shock according to IEC 60068-2-7

Vibration test

15 g / 10–2000 Hz according to IEC 60068-2-6

EMC tests

GOST R IEC 61326-1-2014

CABLE

PIN

FUNCTION

D34

D60

S115

S32

Black

2

1

5

1

Output 1: position

White

5

2

2

2

0 VDC Output 1

Yellow

4

3

3

3

Output 2: position or velocity

Green

5

4

2

-

0 VDC Output 2

-

-

-

5

Output 3: position

Red

1

5

7

7

+24 VDC (-15% / +20%)

Blue

3

6

6

6

0 VDC (power supply)

PIN ASSIGNMENT

PIN

FUNCTION

M16 male connector

(view from sensor side)

1

Output 1: position

2

0 VDC output №1

3

Output 2: position or velocity

4

0 VDC output №2

5

+24 VDC (-15% / +20%)

6

0 VDC (power supply)

AVAILABLE OUTPUT SIGNAL COMBINATIONS FOR D60 CONNECTION CONFIGURATION WITH CABLE OUTLET

Description

Interface order code

Output 1

Output 2

1 output with 1 position magnet

V01

0…10 V

Not applicable

V11

10…0 V

A01

4…20 mA

A11

20…4 mA

PIN ASSIGNMENT

PIN

FUNCTION

M16 male connector (view from sensor side)

1

Output 1: position

2

0 VDC output №1, №2, №3

3

Output 2: position

4

Not applicable 

5

Output 3: position

6

0 VDC (power supply)

7

+24 VDC (-15% / +20%)

8

Not applicable 

VOLTAGE OUTPUT:

CURRENT OUTPUT:

CONNECTION DIAGRAM FOR DEVICE WITH ACTIVE SENSING CHANNEL

CONNECTION DIAGRAM FOR DEVICE WITH PASSIVE SENSING CHANNEL