MSI-HS Series Magnetostrictive Linear Position Sensor with Analog Output

THE SCOPE OF SUPPLY INCLUDES:

Linear position sensor

Certificate of Conformity

Manual

Warranty card

Mating connectors and magnets for the sensor must be ordered separately!

TECHNICAL REQUIREMENTS FOR ORDER PLACEMENT

1

2

3

4

5

6

MSI-HS

.

M

.

0

5

0

0

.

T

.

D60

.

A

0

1

1

Series:

MSI-HS - Rod-Type

2

Flange Type:

M – M18 × 1.5, rod Ø10 mm

G - Plug-in flange 45F7, rod Ø 10 mm

3

Measuring Range:

0025...3800 mm, 1 mm step

Other lengths available on request

4

Zero Point:

T - 50 mm

B - 30 mm

5

Connection:

D34 – M12 (5-pin) male connector

R02 – PVC cable without connector, 2 m; option: R01...R20 (1...20 m)

H02 – PUR cable without connector, 2 m; option: H01...H20 (1...20 m)

6

Output Signal:

A01 - 4…20 mA

A11 - 20…4 mA

V01 - 0…10 V

V11 - 10…0 V

* Measuring range is programmable

Measured quantity

Position

Operating range, L

25 — 3800 mm, 1 mm step

Velocity

0.025 - 10 m/s

Movement speed

Any

Cycle time

0.5 ms up to 1200 mm; 1.0 ms up to 2400 mm;

2.0 ms up to 3800 mm;

Status diagnostics

LEDs next to the connector

INTERFACE

Analog interface

For voltage (control input impedance: > 5 kΩ)

For current (min./max. load resistance: 0/500 Ω)

Number of magnet

1

Max cable length

For stable operation, it is recommended to use a cable no longer than 35 meters

POSITION MEASUREMENT ACCURACY

Resolution

16-bit DAC, 0.0015% (minimum 1 μm)

Linearity deviation

For L ≤ 500 mm: ±50 μm

For L > 500 mm: ±0.01% of the measuring range

Repeatability

< ± 0.001 % F.S. (minimum ± 2.5 µm)

VELOCITY MEASUREMENT ACCURACY

Velocity resolution

0.1 mm/s

Linearity error

< 0.5 %

OPERATING CONDITIONS

Operating temperature

-40 °C…+75 °C

Rated pressure

350 bar, 600 bar peak (optional 800 bar)

Humidity

90 % rel. humidity, no condensation

Ingress protection 

IP65, IP67 at cable outletat cable outlet

MATERIALS

Sensor electronics housing

Anodized aluminum

Sensor rod

Stainless steel ASTM A269-13 / TP304l (10x1.5)

Flange

Stainless steel 08Х18Н10 / AISI 304

MOUNTING

Mounting position

Any orientation. For horizontal installation of sensors with an operating range exceeding 1000 mm, the rod must be supported or fixed at the end

Flange parameters

Flange thread M18х1.5, M22 x 1.5 or 3/4" - 16 UNF

Position magnet attachment

Mounting hardware and screws made of non-magnetic material

ELECTRICAL CONNECTION

Operating voltage

For L < 2500: +12/24 VDC (-10% / +20%)

For L > 2500: +24 VDC (-15% / +20%)

Reverse polarity protection

up to –30 V DC

Overvoltage protection

up to 36 V DC

Current consumption

50…140 mA (depending on sensor length)

Insulation resistance

500 V DC (between sensor housing and 0 V DC)

STANDARDS, EMC TESTS

Shock test

100 g, single shock according to IEC 60068-2-7

Vibration test

15 g / 10–2000 Hz according to IEC 60068-2-6

EMC Tests

GOST R IEC 61326-1-2014

PIN CONFIGURATION D34

PIN

OUTPUT

M12-A male connector

(view from sensor side)

1

+24 VDC (-15% / +20%)

2

Output 1: position

3

0 VDC (power supply)

4

Output 2: position

5

0 VDC output №1, 2

VOLTAGE OUTPUT:

CURRENT OUTPUT:

CONNECTION DIAGRAM FOR DEVICE WITH ACTIVE SENSING CHANNEL

CONNECTION DIAGRAM FOR DEVICE WITH PASSIVE SENSING CHANNEL