MSI-HE Series Linear Position Sensor with Start/Stop Output

THE SCOPE OF SUPPLY INCLUDES:

Linear position sensor

Certificate of Conformity

Manual

Warranty card

Mating connectors and magnets for the sensor must be ordered separately!

TECHNICAL REQUIREMENTS FOR ORDER PLACEMENT

1

2

3

4

5

6

MSI-H

.

S

.

0

5

0

0

.

T

.

D60

.

R01

1

Series:

MSI-H - Rod-type

2

Flange type:

M – M18 × 1.5, rod Ø10 mm

S – 3/4”-16 UNF, rod Ø10 mm

R – M18 × 1.5 with M4 thread on rod end, Ø10 mm

Z – 3/4”-16 UNF with M4 thread on rod end, Ø10 mm

T – 3/4”-16 UNF with raised face, Ø10 mm

V – M18 × 1.5 with FKM seal, Ø10 mm

U – 3/4”-16 UNF with raised face, FKM seal, Ø10 mm

H – 3/4”-16 UNF, FKM seal, Ø10 mm

L – 3/4”-16 UNF, rod Ø7 mm

K – M18 × 1.5, rod Ø7 mm

R - M18 x 1.5, with M4 thread on rod end, rod Ø 10 mm

3

Measuring range:

0025...2500 mm, 1 mm step

Other lengths available on request

4

Zero point:

T - 50 mm

B - 30 mm

5

Connection:

D60 – 6-pin male connector, M16

D84 – 8-pin male connector, M12

GDM – 4-pin, IP65

R02 – PVC cable without connector, 2 m; option: R01...R20 (1...20 m)

H02 – PUR cable without connector, 2 m; option: H01...H20 (1...20 m)

T02 – PTFE cable without connector, 2 m; option: T01...T20 (1...20 m)

S02 – Teflon cable without connector, 2 m; option: S01...S20 (1...20 m)

W02 – Water-resistant cable without connector, 2 m; option: W01...W20 (1...20 m)

6

Output signal:

R01 – Start/Stop

R5 – Start/Stop for injection molding machines

Measured value

Position

Operating range, L

25 — 2500 mm, 1 mm step

Displacement speed

Any

Update rate

0.5 ms up to 1200 mm; 1.0 ms up to 2500 mm

Status diagnostics

LEDs next to the connector

INTERFACE

Digital interface

RS-485/422

Data transfer protocol

Start/Stop

Number of magnets

1

Max cable length

For stable operation, it is recommended to use a cable no longer than 50 meters

POSITION MEASUREMENT ACCURACY

Linearity

Repeatability

OPERATING CONDITIONS

Operating temperature

-40 °C…+75 °C

Rated pressure

350 bar, 600 bar peak

Humidity

90 % rel. humidity, no condensation

Ingress protection 

IP65, IP67 at cable outlet

MATERIALS

Sensor electronics housing

Aluminum, plastic

Sensor rod

Stainless steel ASTM A269-13 / TP304l (10x1.5)

Flange

Stainless steel 08Х18Н10 / AISI 304

MOUNTING

Mounting position

Any orientation. For horizontal installation of sensors with an operating range exceeding 1000 mm, the rod must be supported or fixed at the end

Flange parameters

Flange thread M18х1.5 or 3/4" - 16 UNF

Position magnet mounting

Mounting hardware and screws made of non-magnetic material

ELECTRICAL CONNECTION

Operating voltage

+12 VDC (-15% / +20%)

Reverse polarity protection

up to –30 V DC

Overvoltage protection

up to 36 V DC

Current consumption

up to 35 mA (depending on sensor length)

Insulation resistance

500 V DC (between sensor housing and 0 V DC)

STANDARDS, EMC TESTS

Shock test

100 g, single shock according to IEC 60068-2-7

Vibration test

15 g / 10–2000 Hz according to IEC 60068-2-6

EMC tests

GOST R IEC 61326-1-2014

CABLE

D60

FUNCTION

Black

1

Stop (-)

White

2

Stop (+)

Yellow

3

Start (+)

Green

4

Start (-)

Red

5

+24 VDC (-15% / +20%)

Blue

6

0 VDC (power supply)

PIN ASSIGNMENT

PIN

FUNCTION

M16 male connector

(view from sensor side)

1

Stop (-)

2

Stop (+)

3

Start (+)

4

Start (-)

5

+24 VDC (-15% / +20%)

6

0 VDC (power supply)

PIN ASSIGNMENT

PIN

FUNCTION

M12-A male connector

(view from sensor side)

1

Start (+)

2

Start (-)

3

Stop (+)

4

Stop (-)

5

Not applicable

6

Not applicable

7

+24 VDC (-15% / +20%)

8

0 VDC (power supply)

CONNECTION DIAGRAM FOR THE DEVICE (Duplex)

CONNECTION DIAGRAM FOR THE DEVICE (Half-Duplex)

LED DIAGNOSTICS

GREEN

RED

STATUS

Off

Off

No power supply or sensor fault

On

Off

Normal operation

On

On

No position magnet or incorrect number of magnets

Flashing

Off

Programming mode ( analog output only)