MSI-H Series Magnetostrictive Linear Position Sensor with SSI Output

THE SCOPE OF SUPPLY INCLUDES:

Linear position sensor

Certificate of Conformity

Manual

Warranty card

Mating connectors and magnets for the sensor must be ordered separately!

TECHNICAL REQUIREMENTS FOR ORDER PLACEMENT

1

2

3

4

5

6

7

8

9

10

11

MSI-H

.

S

.

0

5

0

0

.

T

.

D70

.

S

1

B

2

1

0

0

1

Series:

MSI-H - Rod-Type

2

Flange Type:

M – M18 × 1.5, rod Ø10 mm

S – 3/4”-16 UNF, rod Ø10 mm

R – M18 × 1.5 with M4 thread on rod end, Ø10 mm

Z – 3/4”-16 UNF with M4 thread on rod end, Ø10 mm

T – 3/4”-16 UNF with raised face, Ø10 mm

V – M18 × 1.5 with FKM seal, Ø10 mm

U – 3/4”-16 UNF with raised face, FKM seal, Ø10 mm

H – 3/4”-16 UNF, FKM seal, Ø10 mm

L – 3/4”-16 UNF, rod Ø7 mm

K – M18 × 1.5, rod Ø7 mm

R - M18 x 1.5, резьба M4 в конце, шток Ø 10 мм

3

Measuring Range:

0025...6000 mm, 1 mm step

Other lengths available on request

4

Zero Point:

T - 50 mm

B - 30 mm

5

Connection:

D70 – M16 (7-pin) male connector

S32 – M16 (8-pin) male connector

D84 – M12 (8-pin) male connector

R02 – PVC cable without connector, 2 m; option: R01...R20 (1...20 m)

H02 – PUR cable without connector, 2 m; option: H01...H20 (1...20 m)

T02 – PTFE cable without connector, 2 m; option: T01...T20 (1...20 m)

S02 – Silicone cable without connector, 2 m; option: S01...S20 (1...20 m)

W02 – Moisture-resistant cable without connector, 2 m; option: W01...W20 (1...20 m)

6

Output Signal:

S - SSI

7

Parallel code length:

1 – 25 bits

2 – 24 bits

3 – 26 bits

8

Coding:

B – Binary

G – Gray code

9

Resolution:

  mm

μ

1 - 0,005

2 - 0,01

3 - 0,05

4 - 0,1

5 - 0,02

6 - 0,002

7 - 0,04

8 - 0,001

 5

 10

 50

 100

 20

 2

 40

 1

10

Version:

1 – Standard

11

Options:

00 – Forward measuring direction, asynchronous mode

01 – Reverse measuring direction, asynchronous mode

02 – Forward measuring direction, synchronous mode

05 – Forward measuring direction, with 26-bit parallel code length:

25 bits = alarm;

26 bits = parity check

16 – Forward measuring direction, synchronous mode, internal linearization

Measured quantity

Position

Operating range, L

25 — 6000 mm, 1 mm step

Movement speed

Any

Update rate

0.5 ms up to 1200 mm; 1.0 ms up to 2400 mm;

2.0 ms up to 3800 mm;

Status diagnostics

LEDs next to the connector

INTERFACE

Digital Interface

RS 422

Data Transfer Protocol

SSI – Synchronous Serial Interface

Data format: Binary coding or Gray code (24...26 bits)

Number of magnet

1

Max cable length

Cable length, m: 

Baud rate, Mbit/s: 

<3

 1000

<50

<400

<100

<300

For stable operation, it is recommended to use a cable no longer than 20 meters with a data transmission rate not exceeding 500 kBaud.

POSITION MEASUREMENT ACCURACY

Linearity deviation

< ± 0.01 % F.S. (minimum ± 40 µm)

Repeatability

< ± 0.001 % F.S. (minimum ± 2.5 µm)

OPERATING CONDITIONS

Рабочая температура

-40 °C…+85 °C

Номинальное давление

350 bar, 600 bar peak (optional 800 bar)

Точка росы, влажность

90 % rel. humidity, no condensation

Класс защиты

IP65, IP67 at cable outletat cable outlet

MATERIALS

Sensor electronics housing

Anodized aluminum

Sensor rod

Stainless steel ASTM A269-13 / TP304l (10x1.5)

Flange

Stainless steel 08Х18Н10 / AISI 304

MOUNTING

Mounting position

Any. When the sensor is installed horizontally with a measuring range exceeding 1000 mm, its rod must be supported or secured at the end.

Flange parameters

Flange thread M18х1.5, M22 x 1.5 or 3/4" - 16 UNF

Position magnet attachment

Mounting hardware and screws made of non-magnetic material

ELECTRICAL CONNECTION

Operating voltage

For L < 2500: +12/24 VDC (-10% / +20%)

For L > 2500: +24 VDC (-15% / +20%)

Reverse polarity protection

up to –30 V DC

Overvoltage protection

up to 36 V DC

Current consumption

50…140 mA (depending on sensor length)

Insulation resistance

500 V DC (between sensor housing and 0 V DC)

STANDARDS, EMC TESTS

Shock test

100 g, single shock according to IEC 60068-2-7

Vibration test

15 g / 10–2000 Hz according to IEC 60068-2-6

EMC Tests

GOST R IEC 61326-1-2014

WIRE

PIN

FUNCTION

D70

S32

Black

1

5

Data (-)

White

2

2

Data (+)

Yellow

3

1

Clock (+)

Green

4

3

Clock (-)

Red

5

7

+24 VDC (-15 / +20 %)

Blue

6

6

0 VDC (Power supply)

D70 CONNECTOR PIN ASSIGNMENT

PIN

FUNCTION

M16 male

(view from sensor side)

1

Data (-)

2

Data (+)

3

Clock (+)

4

Clock (-)

5

+24 VDC (-15 / +20 %)

6

0 VDC (Power supply)

7

Not connected

S32 CONNECTOR PIN ASSIGNMENT

PIN

FUNCTION

M16 male

(view from sensor side)

1

Clock (+)

2

Data (+)

3

Clock (-)

4

Not connected

5

Data (-)

6

0 VDC (Power supply)

7

+24 VDC (-15 / +20 %)

8

Not connected

PIN CONFIGURATION

D84

PIN

OUTPUT

M12 male connector

(view from cable entry side)

1

Clock (+)

2

Clock (-)

3

Data (+)

4

Data (-)

5

Not connected

6

Not connected

7

+24 VDC (-15 / +20 %)

8

0 VDC (Power supply)

SSI PROTOCOL TIMING DIAGRAM

This oscillogram shows a standard SSI transmission.

Channel 1 reads the clock signal "Clock (+)"

Channel 2 reads the binary code "Data (+)"

The interval between two transmissions (Monoflop time) is 16 microseconds. This performance corresponds to Temposonics V series sensors.

As a result, our sensors are compatible with all controllers currently available on the market.**

DEVICE CONNECTION DIAGRAM

MSI-253 135 PROGRAMMER

Description:

USB-SSI programmer for digital sensors of the following series:

MSI-H,

MSI-P,

MSI-D,

MSI-F,

MSI-B.

Functions:

Zero point programming;

Ability to modify all SSI parameters;

Sensor functionality diagnostics.

Scope of delivery:

Programmer art. no. MSI-253 135 for SSI linear position sensors (1 pc.);

Power supply 220 VAC → 24 VDC (1 pc.);

USB cable (1 pc.);

Ring-shaped position magnet art. no. MSI-201 542-2 (1 pc.);

Connection cable for sensor with D70 connector (1 pc.);

Connection cable for sensor with S32 connector (1 pc.);

User manual (1 pc.).

LED DIAGNOSTICS

GREEN

RED

STATUS

Off

Off

No power supply or sensor fault

On

Off

Normal operation

On

On

No position magnet or incorrect number of magnets

Depends on status

Off

Programming mode, accessible via USB-SSI programmer art. no. MSI-253 135