MSI-P Series Magnetostrictive Linear Position Sensors In Profile Housing With DeviceNet Output

THE SCOPE OF SUPPLY INCLUDES:

Linear position sensor

Certificate of Conformity

Manual

Warranty card

Mating connectors and magnets for the sensor must be ordered separately!

TECHNICAL REQUIREMENTS FOR ORDER PLACEMENT

1

2

3

4

5

6

7

8

9

10*

MSI-P

.

S

.

0

5

0

0

.

T

.

D60

.

С

1

0

1

1

1

1

Series:

MSI-P - Profile housing

2

Magnet Type:

– Without magnet

S – Magnetic slider “S”, mechanically coupled, free travel

SP – Magnetic slider “SP”, mechanically coupled, close-fit design

L – Position magnet “L”, air gap up to 10 mm

K – Position magnet “K”, air gap up to 4 mm

3

Measuring Range:

0025...4000 mm, 1 mm step

Other lengths available on request

4

Zero Point:

T - 13 mm

5

Connection:

D60 – M16 (6-pin) male (Sensor with integrated bus terminator)

D61 – M16 (6-pin) male

6

Output Signal:

C202 - DeviceNet

7

Data rate:

1 – 500 kbit/s

2 – 250 kbit/s

– 125 kbit/s

8

Resolution:

1 – 5 μm

2 – 2 μm

9

Type:

1 – Standard

10*

Option 1:

Not applicable / None

ER1: Extending rod with stabilizer for standard sensor mounting.

Measured quantity

Position

Operating range, L

25 — 4000 mm, 1 mm step

Movement speed

Any

Cycle time

0.5 ms up to 1200 mm; 1.0 ms up to 2400 mm;

2.0 ms up to 4000 mm;

Status diagnostics

LEDs next to the connector

INTERFACE

Digital interface

CAN FieldBus System ISO 11898

Data protocols:

DeviceNet v. 2.0

Number of magnet

1

Max cable length

For stable operation, it is recommended to use a cable no longer than 50 meters.

POSITION MEASUREMENT ACCURACY

Linearity deviation

< ± 0.01 % F.S. (minimum ± 40 µm)

Repeatability

< ± 0.001 % F.S. (minimum ± 2.5 µm)

OPERATING CONDITIONS

Operating temperature

-40 °C…+85 °C

Rated pressure

350 bar, 600 bar peak (optional 800 bar)

Humidity

90 % rel. humidity, no condensation

Ingress protection 

IP65, IP67 at cable outletat cable outlet

MATERIALS

Sensor electronics housing

Anodized aluminum, plastic

Sensor rod

Stainless steel ASTM A269-13 / TP304l (10x1.5)

Flange

Stainless steel 08Х18Н10 / AISI 304

MOUNTING

Mounting position

Any

For L < 500: Use 2 clamping brackets

For L > 500: Add 1 clamping bracket every 500 mm

Profile

Movable mounting clamps

Position magnet attachment

Mounting hardware and screws made of non-magnetic material

ELECTRICAL CONNECTION

Operating voltage

For L < 2500: +12/24 VDC (-10% / +20%)

For L > 2500: +24 VDC (-15% / +20%)

Polarity protection

Up to −30 VDC

Overvoltage protection

Up to 36 VDC

Current consumption

50…140 mA (depending on stroke length)

Dielectric strength

500 VDC (DC ground to machine ground)

STANDARDS, EMC TESTS

Shock test

100 g, single shock according to IEC 60068-2-7

Vibration test

15 g / 10–2000 Hz according to IEC 60068-2-6

EMC Tests

GOST R IEC 61326-1-2014

PIN CONFIGURATION

PIN

OUTPUT

M16 male

(View on sensor)

1

CAN_LOW

2

CAN_HIGH

3

-

4

-

5

+24 VDC (−15/+20 %)

6

DC Ground (0 V)

PIN CONFIGURATION

PIN

OUTPUT

M16 male

(View on sensor)

1

CAN_LOW

2

CAN_HIGH

3

-

4

-

5

+24 VDC (−15/+20 %)

6

DC Ground (0 V)

LED DIAGNOSTICS

GREEN

RED

STATUS

Off

Off

No power supply or sensor fault

On

Off

Normal operation

On

On

No position magnet or incorrect number of magnets

Flashing

Off

Programming mode ( analog output only)